Plumbing for Beginners: The Essentials for Installing a Bathtub
Plumbing for Beginners: The Essentials for Installing a Bathtub
Blog Article
They are making a number of good points related to How to Install a Bathtub in general in this article further down.
Setting up a bathtub isn't exactly brain surgery, but it does need solid plumbing, carpentry, and occasionally, tiling skills. Replacing an old bathtub with a brand-new one is likewise a moderately hard job. If the old bathtub is easily accessible, the project can relocate speedily; if you need to open a wall to eliminate the old bathtub and also position the brand-new bathtub, the job is much harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old tub and embeded in the brand-new one. Make certain you have actually certified yourself for the work and also fit trying it. Rather than working with a specialist to take control of a halfway-completed project, it is much better to consider using one prior to you start. Chances are you might require a specialist plumber to make tube connections.
This short article will assist you mount a brand-new tub in your bathroom if you have currently purchased a new bathtub as well as do not require to change the setup of your previous water pipes.
Your devices and also material checklist ought to consist of the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, after that the first thing you ought to do is disconnect the supply of water. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The process of getting rid of the existing taps can be fairly troublesome as a result of the restricted gain access to that is often the situation.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a cloth all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipes have actually been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this process. When the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old sealing compound.
Prior to proceeding to fit the new faucets, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the tap as well as the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin making sure that the washing machines remain in place between the faucet as well as the sink. Protect the tap in position with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular tap ports. The former type should be linked to the tap finishes first, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Tub
Utilizing the two wooden boards under its feet, position the bathtub in the required placement. The wood boards are useful in equally spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to guarantee that the tub is leveled all round. This can be attained by checking the level and also adjusting the feet on the bathtub till the spirit level reads level.
To install taps, fit all-time low of the outermost flexible faucet port to the proper supply pipe by making a compression join; then do the very same for the other tap.
Switch on the water as well as examine all joints and also new pipework for leakages as well as tighten them if essential. Fill the tub and additionally inspect the overflow electrical outlet and also the normal outlet for leakages.
Lastly, fix the bath paneling as explained in the manufacturer's instruction manual. Tiling and sealing around the bath tub ought to wait until the bathtub has actually been used at least when as this will resolve it into its final placement.
Getting ready for the Setup
Firstly, the sustaining framework supplied with the bathroom ought to be fitted (if required) according to the maker's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to avoid pressure on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you make use of all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its last placement.
Tiling Around the Tub
In the area where the bathroom satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the fitting can move enough to split a stiff seal, creating the water to permeate the wall surface in between the bathroom as well as the tiling, bring about problems with wetness and also possible leakages to the ceiling below.
You can pick from a selection of coloured sealers to blend in your fixtures and installations. They are marketed in tubes and also cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water before securing, to enable the movement experienced when the tub is in usage. The sealant can fracture relatively very early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or water resistant glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very occupied with A Step-by-Step Guide to Installing a Bathtub and I hope you appreciated the new post. Do you know about somebody else who is in to the niche? Be sure promote it. Thanks a bunch for your time. Visit again soon.
Drain woes? Connect. Report this page